سعر فوب
أحصل على آخر سعر65 ~ 90 / Set
|1 Set Minimum Order
بلد:
China
نموذج رقم:
OW-CP01
سعر فوب:
65 ~ 90 / Set أحصل على آخر سعر
الموقع:
Zhejiang
سعر الحد الأدنى للطلب:
65 per Set
الحد الأدني للطلب:
1 Set
تفاصيل التغليف:
Cap Machine 39*24*36cm
موعد التسليم:
3 days after payment
القدرة على التوريد:
5000 Set per Month
نوع الدفع:
-
مجموعة المنتج :
الشخص الذي يمكن الاتصال به Ms. Jasmine
Jiangbei Industrial Park, Jinhua, Zhejiang
CAP-PRESS MACHINE INSTRUCTION
CAUTION:
1.for continued protection against fire,disconnect power-supply before using the machine,check the power-supply grounded connection well before using.
2.Disconnect power-supply before replacing different-function heat unit
3.Put in the object going to be shaped,close up the pressure handle and rotate the adjusting screw to get a proper pressure.
4.The surface of the heat unit is hot during heat pressing,do not touch then with no proper protection.
BASIC PREPARATION BEFORE USING
1.plug the power line into the outlet,check whether the power supply is conformity with the rated voltage of the machine ,there should be a reliable ground wire for the power supply.
2,Put in the object going to be shaped.
3.turn on the power switch,and the instrument board will display the temperature.
4.Set the temperature and time according to the table below and get the specific corresponding and timing setting.
Initial temperature highest temperature time
Single process **0 **0 *0
Continuous process **5 **0 **0
LEARN TO SET THE TEMPERATURE AND TIME
1.press the model key once,see theset lightturning red.press the plus or minus key to set initial heating temperature.
2.Press the mode key for the second time,see the temperature lightturning red,press the plus or minus key to set the proper heating temperature.
3.Press the mode key for the third time,see the time lightturning red,press the plus or minus key to set the proper heating time.
4.Press the mode key for the fourth time,finish the setting and the machine stands by to work.
ATTENTION:
The initial heating temperature should be set between ******0,the highest heating temperature should be set between ******0.the timing should be set between ****9sec.
If the initial heating temperature is **0,the highest heating temperature should be set only between ******0.as the same,if the highest heating temperature is **0,the initial heating temperature should be set only between ******0.initial heating temperature always =
OPERATION
Press the corresponding temperature and time for the object that is going to be shaped.put into the object,close up the pressure handle,press the executive key,the temperature will straight to achieves the highest heating temperature ,wait for a few times(set),you will hear a hint sound,the pressing is finished,pull up the pressure handle,press the executive key.Do the next object or turn off the power.
|
بلد: | China |
نموذج رقم: | OW-CP01 |
سعر فوب: | 65 ~ 90 / Set أحصل على آخر سعر |
الموقع: | Zhejiang |
سعر الحد الأدنى للطلب: | 65 per Set |
الحد الأدني للطلب: | 1 Set |
تفاصيل التغليف: | Cap Machine 39*24*36cm |
موعد التسليم: | 3 days after payment |
القدرة على التوريد: | 5000 Set per Month |
نوع الدفع: | - |
مجموعة المنتج : | Heat press machine |