سعر فوب
أحصل على آخر سعر( Negotiable )
|1000 Meter Minimum Order
بلد:
China
نموذج رقم:
-
سعر فوب:
( Negotiable )أحصل على آخر سعر
الموقع:
-
سعر الحد الأدنى للطلب:
-
الحد الأدني للطلب:
1000 Meter
تفاصيل التغليف:
-
موعد التسليم:
-
القدرة على التوريد:
1000000 Meter per Month
نوع الدفع:
T/T, L/C, D/A, D/P, Western Union
مجموعة المنتج :
الشخص الذي يمكن الاتصال به Jason
Xinyu, Jiangxi
Aluminum cable features Description:
The density of aluminum conductor itself is
relatively small copper cable, light weight aluminum cable
specifications section, the relative carrying construction laying
easier. The most obvious advantage is that the same types of
specifications aluminum cable cheap. Usually about *0% of the same
size copper cable prices. The carrying capacity is about *0% of the
copper cable. Significantly lower investment cost, cost-effective.
Suitable for low-budget works or temporary power. But also because
they are inexpensive, unattended mines and other areas of the site
easily stolen. Also in the copper conductor corrosive conditions or
ammonia compressor room, large span overhead transmission lines,
larger cross-section adapted to other environmental IF line
aluminum cable.
Since the resistivity of aluminum conductors
large line losses and voltage drop is relatively high, and the
relative strength of copper ductility is poor, easily oxidized
corrosion and other characteristics, in some cases should not use
aluminum.
Power cable installation considerations, the use of properties and
operating conditions laid
1, Power Cable Installation Considerations
Cable and heat pipe parallel to maintain a distance of 2m to
install the cross should be kept 0.5m.
Cables and other pipes are to maintain a distance of 0.5m
when installed parallel or cross.
When buried cable installation, ***5KV cable buried depth of
not less than 0.7m.
When *0KV and the following cables installed in parallel with
each other spacing is not less than 0.1m, ****5KV not less than
0.*5m; when cross-installation distance of not less than 0.5m.
Cable laying temperature not lower than 0 ºC, bending radius:
multi-core cable ≥*5 (D + d), single-core cable ≥*0 (D + d), (D is
the cable diameter, d is the outer diameter of the conductor).
6KV and over cable connector:
When installation 1,Cable Terminal, must strip
semiconductor electrical shielding layer, the operation should not
damage the insulation, should avoid the uneven marks, if necessary,
polished with sandpaper; shield ends should be smooth, and put
graphite layer (carbon tablets) cleaned.
2 plastic insulated cable end copper and steel armor shield
must be grounded to short circuit this principle and avoid
unbalanced three-phase running steel armor end induced
electromotive force, even "ignition" combustion jacket and other
accidents . Lead grounding applications require the use of my
tinned braided copper wire, copper cable and connect ferrochrome
soldering, should not use the blowtorch to avoid burning
insulation.
3,three-phase Copperbelt shield should be connected to the
ground, respectively, pay attention to the grounding wire and steel
armor shielded grounding wire should be separately leads, insulated
from each other, welding ground should be the lower position.
On the cable ends and the middle joint of the basic
requirements:
. A conductor connected;
. B insulation reliable, recommended
irradiation cross-linked heat shrinkable silicone rubber insulating
material;
. C a good seal;. D sufficient
mechanical strength, can adapt to various operating conditions.
Cable ends must be used to prevent the erosion of
water and other corrosive materials, to prevent water tree caused
by insulation breakdown caused by aging.
Cable handling crane or forklift must prohibit
the transport flat, flat, to be put to use when a large cable car
cable installation, in order to avoid cable damage by external
forces or because of artificial drag and abrasions. If for some
reason can not be cable laying, it should be stored in a dry place,
away from direct sunlight to prevent, water and other cable ends.
Note: wire and cable wire and cable installation should be familiar
with the performance of the installer or as a full-time technical
staff, such as the matter is still not clear, ask the relevant
technical department or consult factory technical department.
2, using the properties of the cable laying and operating
conditions
* Rated voltage 0.6 / 1KV PVC insulated power cable
1,cable conductor long-term allowable working
temperature: ≤*0 ºC
When 2,short (the longest duration of no more
than 5S) maximum operating temperature of the cable: **0 ºC
3, Cabling after being subjected to a DC voltage 3.5KV /
*5min without breakdown.
4, laid in the air
a center distance of
single-core cable laying parallel: **5mm2 and below 2 times the
cable diameter: **0mm2 and above *0mm
. B Ambient temperature:
*0 ºC
* Rated voltage *5KV and below XLPE insulated power cable
1 cable conductor long-term allowable working
temperature: ≤*0 ºC
When 2short (the longest duration of no more than
5S) maximum operating temperature of the cable: **0 ºC
3,air laying
a single-core cables laid in
parallel from the center when:. **5mm2 and below 2 times the cable
diameter: **0mm2 and above *0mm
. B Ambient temperature: *0
ºC
4, Buried
a. Single core cables are
installed, the center distance of 2 times the cable diameter
b ambient temperature:. *5
ºC
c soil thermal resistivity:.
1.0K · m / W
. D Buried Depth: 0.7m
Aluminum insulated wire ampacity multiple relationships with section
بلد: | China |
نموذج رقم: | - |
سعر فوب: | ( Negotiable ) أحصل على آخر سعر |
الموقع: | - |
سعر الحد الأدنى للطلب: | - |
الحد الأدني للطلب: | 1000 Meter |
تفاصيل التغليف: | - |
موعد التسليم: | - |
القدرة على التوريد: | 1000000 Meter per Month |
نوع الدفع: | T/T, L/C, D/A, D/P, Western Union |
مجموعة المنتج : | xlpe insulated cable |