Sell Power monitoring socket

Description

A, function 1, detection environmental voltage and frequency 2, monitor socket current, power (with or without power), power factor 3, the countdown measures: Measurement set (day - hours -minute), to record total electricity consumption within the setting value of the socket, the maximum time value is *9 days *3 hours *9 minutes. 4, sub-accounting functions: The socket supports two billing rates, hours and rates can be established. B, Appearance Color: Gray Dimensions: *0 cm × 7cm × 4cm Weight: C, Technical indicators 1, accuracy: voltage, current, power factor accurate to three decimal; other items accurate to two decimal. 2, environmental conditions Voltage: rated **0 V, adaptation V **0 ~ **0: Rated current 2.5 A, maximum current *0 A Frequency: *5 ~ *5 Hz temperature: **0 °C ~ *0 °C relative humidity ≤ *5% 3, electric measurement error: less than 0.5% under Rated working environment D, use of methods 1, setting By clicking "SET" button to shift to the pages of the content needed to set up, and then click " " button to select a place needed to amend, the selected place will be flashing, click "â–&frac*4;" button to amend the value. Click "SET" button again after the amendment to confirm changes when the set -up value is illegal, it will then be automatically corrected. To give up the new settings before click the "SET" button to confirm the amendment, stop for five seconds after operating, and the socket will automatically switch to the normal status, in which case the last item amended will not take effect. See table (1) for details on the content, format, value and related content. (A) set list Order items prompted characters value setting format maximum range 1 starting time of phase I Hr: Min: *0ï&frac*4;š*0~*3ï&frac*4;š*9 2 starting time of phase II Hr: Min: *0ï&frac*4;š*0~*3ï&frac*4;š*9 3 rate of phase I metric *0.*0 0.*1~*9.*9 4 rate of phase II metric *0.*0 0.*1~*9.*9 5 countdown time: Day. Hr: Min: *9 days *3 hours *9 minutes 6 Date year month day any legitimate date 7 time: hour min: sec any legal time of the **-hour time system 2, flip enquiries (A) In the non-setting state, click "â–&frac*4;" button to flip and view the contents within the system, *0 seconds after operating the system will be automatically converted to circulation display, if click "" button within *0 seconds, will be postponed *0 seconds , And so on. See table (2) for the order, content of display, tips, characters, ***** flip inquiry. (B) flip inquiry form Order items prompted characters show format 0 time: Hour min: sec NN:NN:NN 1 Date year month day ***** 2 TotalActive electric energy ***** (KWh) 3 Active 1 ***** (KWh) 4 Active 2 ***** (KWh) 5 Total Electric fee *****(units in line with set rates) 6 Countdown surplus duration Day. Hr: Min 7 Countdown electric quantity ***** (KWh) 8 voltage ***** (V) 9 current ***** (A) *0 power ***** (W) *1 reactive power ***** (VAR) *2 frequency ***** (Hz) *3 start time of phase I: HOURï&frac*4;šMINUTE NNï&frac*4;šNN *4 start time of phase II : HOURï&frac*4;šMINUTE NNï&frac*4;šNN *5 rate of phase I ***** ï&frac*4;ˆï¿¥/$ï&frac*4;‰ *6 rate of phase II ***** ï&frac*4;ˆï¿¥/$ï&frac*4;‰ *7 total reactive power ***** (KVARH) *8 reactive one ***** (KVARH) *9 reactive two ***** (KVARH) *0 Power Factor 3, cycle display Power system automatically enter cycle display mode, every five seconds for a page shit, click the "" button within five seconds to defer the time. Items displayed has been set within the factory. 4, clear cumulative power Hold down the "SET" button for over two seconds and then release, the system will automatically clear the cumulative power before, then re-start total electricity consumption accounting. Note: This operation does not eliminate the countdown measurement of electricity, the countdown electricity will be automatically cleared after each set. E. Note 1, the socket without waterproof function, once in water should immediately pulling away from the power, so as to avoid damage to electrical equipment within the socket board, and on dry-ventilated places to be able to fully dry up before next use. 2, voltage range of the socket board measurement functions is **0 V ~ **0V, will not be able to quantify for voltage beyond the scope and work long hours beyond the scope, will damage socket board or accelerated aging of socket board. 3, on-rechargeable button-type battery for the socket board , the shortest life of 2.5 years, continuing use after the end of life may arise problem of date and time inaccuracy, in which case, simply replace the Button batteries of model "CR***2" within the socket board for continuing use.