Description
Purpose:
Waste tire recycling system is used to shred waste tire into rubber
powder.
Process Flow:
Waste tire*-Ring cutter *-Strips cutter*-Rim cutter *-Crushing
machine*-Finished products.
Processing Method:
Physic mechanical crushing method at normal temperature of waste
tire, no chemical raw material is required, no waste gas, waste
water and soot are discharged, and the cooling water of the
equipment is reused, no emission, equipment noise is within the
range specified by the country(GB*********6), fineness of rubber
powder produced by it is adjustable(*0 to *0 meshes). The process
is as follows: Breaking down, crushing, filtering, magnetic
separating, grinding and then be finished.
Ring cutter:
Usage:
1. It will cut the whole tire into sidewall of tire and inner
circle.
2. Easy to operate and safety.
Productivity *0 Piece/h
Power 3KW
Adapt tire ********0mm
Dimensions ***0***0****0(mm)
Structural principle:
1. The device consists of frame, motor, reducer, transmission,
supporting frames, knife, tools and other components.
2. Knife is made from alloy and hard waer-resisting.
3. Motor and reducer connected by coupling, compact structure,
simple operation, easy maintenance.
Function:
1. It will separate the sidewall from the top of tire's connection,
so that tire sidewall and the top are completely separated.
Strips cutter:
Usage
1. It can cut all kind of tires, rubber sheets into strips.
Productivity *0 Piece/h
Power 4KW
Adapt tire ********0mm
Dimensions ***0***0****0(mm)
Structural principle
1. This equipment mainly consists of two blades, motor and reducer,
frame and transmission mechanism etc.
2. Knife with special materials, hard wear-resisting, can relapse
grinding use.
3. This equipment shear force, low energy consumption, uses a low
speed, easy operation, safety.
Function
1. It will cut sidewall into wide of strips is **5 cm, and tire
circle reserved.
Rim cutter:
Usage:
1. It will cut the **5cm strips into 3.5cm tire block.
Productivity ***0KG/h
Power 7.5KW
Dimensions ***0***0****0(mm)
Structural principle
1. The device consists of frame, motor, transmission mechanism,
balance equipment, two move knives and a fixed knife, and the
compression gear etc.
2. Knife is made from alloy, hard wear resistant, can be used after
repeatedly grinding.
3. Uniform speed of the device, shear force, low energy
consumption, easy operation and safety.
Steel wire separator
Usage:
1. It will separate the steel and rubber from tire circle mouth
parts.
Productivity *0 PCS/h
Power *1KW
Dimensions ***0***0****0(mm)
Structural principle
1. The device consists of frame, motor, reducer, transmission
mechanism, communication and regulation of body roll and so on.
2. Ditch is made of alloy, roll, hard wear resistant, can be used
repeatedly surfacing repair.
3. This equipment has simple structure, high efficiency, low energy
consumption, strong practical, easy operation, and safety.
Tire shredder
Usage:
1. It will cut 3.5cm block into ****0 mesh size rubber powder.
Structural principle:
1. The equipment consists of one base, frame, front and rear
roller, transmission gear, reducer, motor, adjusting devices,
safety switches and electrical control components.
2. The rollers adopt alloy cold hard cast iron (rollers implement
national standard by HG/T ********8) surface hardness wear and long
life, can be repeatedly repair.
3. The device has low noise, high efficiency, low energy
consumption, simple operation, without any environmental
pollution.
The whole line has the following features:
1. Iron/steel removing ratio>*9.5%, fiber removing
ratio>*8%
2. Compact structure ensures running safety, easy maintenance;
3. Low energy consumption;
4. Adopt semi-automatic control system for whole line, reduce labor
cost;
5. No sewage and waste gas discharge, environment protection.
