FOB Price
أحصل على آخر سعر|
Minimum Order
Place of Origin:
China
Price for Minimum Order:
-
Minimum Order Quantity:
200 Piece
Packaging Detail:
Color Box
Delivery Time:
within a month
Supplying Ability:
20000 Piece per Month
Payment Type:
T/T
الشخص الذي يمكن الاتصال به Mr. Benny
Luqiao,pengjie, Taizhou, Zhejiang
Description :
2. LVLP Spray Gun use of lower volume of air finel atomizes paint creating a smooth finish with minimum overspray.This means very little overspray will be produced,saving on paint cost and environmental hazards.
3. Stainless steel needle and nozzle accommodate a variety of coatings
4. Air volume,paint volume and spraying pettern adjustable.
5. New ergonomic designed handle for comfortable grip.
| Model No. | R**0 |
| Type of feed | Gravity |
| Standard Nozzle | 1.5mm |
| Optional Nozzle |
1.*-1.*-2.0mm
|
Spray Gun Trouble Shooting:
|
Symptom |
Problem | Solution |
| Spray gun's body fluttering or spitting |
1.Spray gun's material level too low. 2.Container tipped too far. 3.Loose spray gun's fluid inlet connection. 4.Loose or damaged spray gun's fluid tip/seat. 5.Dry or loose spray gun's fluid needle packing nut. 6.Spray gun's air vent clogged.
|
1.Add material into spray gun's container. 2.Hold more upright. 3.Tighten. 4.Adjust or replace the spray gun's fluid tip/seat 5.Lubricate or tighten. 6.Clear the spray gun's vent hole.
|
| Pattern is arc |
1.Worm or loose spray gun's fluid nozzle. 2. Spray gun's material build up on air cap.
|
1.Tight or replace spray gun's fluid nozzle. 2.Remove obstructions from holes, but use meatal objects to clean.
|
| Patterm is not evenly spread |
1.Materoa; build up on air cap. 2. Spray gun's fluid nozzle dirty or worn.
|
1.Clean or replace spray gun's air cap. 2.clean or replace spray gun's fluid nozzle.
|
|
The center of pattern too narrow.
|
1. Spray gun's material too thin or not enought. 2.Atomization air pressure too high
|
1.Regulate material viscosity 2.Reduce air pressure.
|
|
Pattern width of fan sharp is not enough
|
1. Spray gun's material too thick 2.Atomization air pressure too low
|
1.Regulate material viscosity 2.Reduce air pressure |
|
Air leaking from air cap without pulling trigger
|
1.Sticking spray gun's valve stem 2.Contaminate on spray gun's air valve or seat 4.Broken spray gun's air valve spring 5.Bent spray gun's valve stem
|
1.Lubricate spray gun's valve stem 2.Clean spray gun's air valve or seat 4.Replace spray gun's air valve spring 5.Replace spray gun's valve stem
|
|
Spray gun fluid leaking from packing nut
|
1.Spray gun 's packing nut loose 2.Spray gun 's packing worm or dry
|
1.Tighten, but do not restrict needle 2.Peplace or lubricate (non-silicone oil)
|
|
Excessive overspray
|
1.Too high atomization pressure 2.Too far from work surface 3.Improper stroking (arcing ,spray gun motion too fast )
|
1.Reduce pressure 2.Adjust to proper distance 3.Move at moderate pace, parallel to surface
|
| Spray gun will not spray |
1.No pressure at spray gun 2.Spray gun 'sfluid control not open enough 3.Spray gun's fluid too heavy
|
1.Check spray gun's air lines 2.Open spray gun's fluid control 3.Thin spray gun's valve stem fluid or change to pressure feed system
|
