Description
1.5KW(**0V) 2.2KW(**0V) 2.2KW(**0V) 3.7KW(**0V)
Plastic Enclosure Dimension:**9x**5x**4.8mm
Model:SKI-E1D5G****0
Power:1.5KW
Input Voltage:single phase/three phase **0V *0Hz
Output Capacity(KVA):2.4/-
Output Current G/P(A):8/-
Suitable Motor G/P(KW):1.5/-
Model:SKI-E2D2G****0
Power:2.2KW
Input Voltage:single phase/three phase **0V *0Hz
Output Capacity(KVA):3.7/-
Output Current G/P(A):*1/-
Suitable Motor G/P(KW):2.2/-
Model:SKI-E2D2G****0
Power:2.2KW
Input Voltage:Three phase **0V *0Hz
Output Capacity(KVA):4.2/-
Output Current G/P(A):6.2/-
Suitable Motor G/P(KW):2.2/-
Model:SKI-E3D7G****0
Power:3.7KW
Input Voltage:three phase **0V *0Hz
Output Capacity(KVA):6.6/-
Output Current G/P(A):8.2/-
Suitable Motor G/P(KW):3.7/-
Control
Method:SVPWM
Control Mode:V/F Control/Current Vector
Control
Torque Feature:with torque compensation and slip
compensation, start torque can reach **0% at 1.0Hz
Frequency Control Range:0.1~**0Hz
Frequency Prcision(Temperature Changing):Digital
Instruction:0.*1%(*0~*0 degree centigrade) Analog
Instruction: Max Frequency x 0.2%Hz(*5 degree centigrade*0%)
Setting Resolution:Digital Instruction:0.*1Hz
Analog Instruction: Max Frequency x 0.1%Hz
Output Resolution:0.*1Hz
Overload Capability:General Mode(G):**0% rating
output current for 1 min, Blower/Pump Model(P):**0% rating output
current for 1min
Frequency Setting Signal:0~*0V(*0kΩ),**4~*0mA
**0Ω
Acceleration/Deceleration Time:0.0~***0
seconds(acceleration/deceleration time sahll be set
respectively)
Braking Torque:About *0% without braking resistor,
and about **5% with braking resistor
V/F Mode Classess:*5 preset V/F modes and
programmable V/F mode
Overload Protection:Electronic thermal overload
relay protection.
Instantaneous OverCurrent:General Mode(G):About
**0% AC motor drive rating current, Blower/Pump Mode(P):About **0%
AC motor driver rating current
Overload:General Mode(G): **0% ratin output
current for 1min before sliding stop, Blower/Pump Mode(P):**0%
rating output current for 1 min before sliding stop
OverVoltage: Motor stops sliding when rectifier
output voltage exceeds **0V(**0V class)/**0V(**0V class)
Under Voltage:Motor stops sliding when rectifier
output voltage drops down to **0V(**0V class)/**0V(**0V class) or
lower.
Instantaneous Power-Failure Compensation:Instant
stop when instantaneous power-failure lasts for *5ms or
longer.(Default setting)According to standard setting, if the
power-failure is shorter than 2 seconds, continue operation.
Heat Sink Overheat:hermistor protection, takes
effect when temperature exceeds **5 degree centigrade.
Speed Loss Protection:Speed loss protection during
acceleration ,deceleration and constnt speed operation
Grounding Failure:Electronic circuit protection,
takes effect when leakage current reaches *0% of AC motor dirver
rating current.
Environment
Temperature/Humidity:*0~*0℃*0RH
and lower(no dewing)
Operation Location: No higher than altitude **0m
above sea leavel, indoor(no corrosive gas, liquid, no dust)
Storage
Temperature:-*0~*0℃
Vibration:*0Hz and
below:9.8m/s2(1G) *0~*0Hz:5.*8m/s2(0.6g)