6X2 CHANNEL RF wireless remote control system

Description

                       This 2 channel DC RF wireless remote control system can used to control lights, motor, fans, electrically operated doors/locks blinds or other appliances automatically. It is easy to install and use. The remote control switch has 2 buttons, and works with toggle, latched, momentary and momentary + toggle 4 control modes. Its control distance is about **0 meters away. It should be a good choice for you. Just take it away!
Note: Customized design is acceptable, we have professional technology-support!
Feature:
 

• Wireless control, easy to install
• Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC **0~**0V or DC 0~*8V.
• You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors.
• With characteristics of over current protection, short-circuit protection and temperature protection.
• Audible / visual indication
• Use microcontroller model of EM*8P**6, an *-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
• Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an *-bit code.
• One/several transmitters can control one/several receivers simultaneously.
• If you use two or more receivers in the same place, you can set them with different codes.
• Transmitting Frequency: The default frequency is **5MHz ,we can also provide **3MHz, you can leave us a message or contact us if you need.
   

• Model No.: H*-DC*2
• Channel: 2 CH
• Control Modes: Toggle, Momentary, Latched, Momentary + Toggle
• Coding Type: Fixed code
• Coding Setting: By learning
• Power Supply (Operating Voltage): DC*2V±1V (H*-DC*2),we can also provide DC*9V or DC*4V,please contact us if you need.
• Working Voltage Range of Relay: AC **0~**0V or DC 0~*8V
• PCB size: *4mm x *2mm x *4mm
• Case size: *9mm x *8mm x *5mm
• Maximum Working Current: *0A
   

• Model No.: HR**2
• Channel: *2 CH
• Remote Control Distance: ***0m / ***0ft (theoretically)
• Encode: Fixed code by Soldering
• Unit size: **5mm x *4mm x *5mm
• Power Supply: 1 x 6F*2 *9V battery (included, can be used for *2 months)

• Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as following operation):
• Setting control mode Toggle: Only connect Jumper*2.
  Control mode Toggle: Press -> On; Press again -> Off.
  Press button A: Turn on the relay (connect B and C, disconnect A and B)
  Press button A again: Turn off the relay (disconnect B and C, connect A and B)
• Setting control mode Momentary: Only connect Jumper*1.
  Control mode Momentary: Press and hold -> On; Release -> Off.
  Press and hold button A: Turn on the relay (connect B and C, disconnect A and B)
  Release button A: Turn off the relay (disconnect B and C, connect A and B)
• Setting control mode Latched: Do not connect Jumper*1 and Jumper*2.
  Control mode Latched: Press -> On, another relay Off; Press another button -> Off.
  Press button A: Turn on the relay (connect B and C, disconnect A and B)
  Press button B: Turn off the relay (disconnect B and C, connect A and B)
• Setting control mode Momentary + Toggle: Connect Jumper*1 and Jumper*2.
  Control mode Momentary (Channel 1): Press -> On; Press again -> Off.
  Press and hold button A: Turn on relay 1 (connect B and C, disconnect A and B)
  Release button A: Turn off relay 1 (disconnect B and C, connect A and B)
  Control mode Toggle (Channel 2): Press and hold -> On; Release -> Off.
  Press button B: Turn on relay 2 (connect B and C, disconnect A and B)
  Press button B again: Turn off relay 2 (disconnect B and C, connect A and B)

• We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver.
  Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored codes have been deleted successfully.
   
•  
  Learning the button of remote control:
  1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
  2) Press button on remote control. If signal LED flashes quickly *5 times and turns off, it means learning is successful.
  Receiver1:press button 1 to learn.
  Receiver2:press button 3 to learn.
  Receiver3:press button 5 to learn.
  Receiver4:press button 7 to learn.
  Receiver5:press button 9 to learn.
  Receiver6:press button 1 to learn.
  3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
  4) The receiver can learn several remote controls with different codes.

• *2 x Receiver: H*-DC*2 (2 Channel / Four Control Modes)
• 1 x Transmitter: HR**2
• 1 x User manual