gas pipe wrapping tape polyethylen butyl adheisve

سعر فوب

أحصل على آخر سعر

2.5 ~ 3.6 / Roll ( Negotiable )

100 Roll Minimum Order

بلد:

China

نموذج رقم:

XUNDA T100

سعر فوب:

2.5 ~ 3.6 / Roll ( Negotiable )(قابل للتفاوض) أحصل على آخر سعر

الموقع:

سعر الحد الأدنى للطلب:

2.5 per Roll

الحد الأدني للطلب:

100 Roll

تفاصيل التغليف:

carton

موعد التسليم:

5-7days

القدرة على التوريد:

3000000 Roll per Month

نوع الدفع:

T/T, L/C

مجموعة المنتج :

XUNDA T100

الاتصال الآن

Jining Xunda Pipeline coating materials Co., Ltd

China

عضو مجاني

الشخص الذي يمكن الاتصال به Mr. Spark

Chenguang Road, No. 1, Rencheng Industry District, Jining, Shandong

الاتصال الآن

مواصفات المنتج

Other Names:polyethylene anti-corrosion tape
Place of Origin:Shandong, China (Mainland)
Main Raw Material:PE ,butyl rubber
Thickness: 0.5mm(20mil), 0.63mm(25mil)
Width: 2\'\'(50mm), 4\'\'(100mm),6\'\
Length:200ft(60M), 400ft(120M), 600ft(180M

الوصف

gas pipe wrapping tape polyethylen butyl adheisve
inner wrap tape is extensively used in the pipework of oil,water and natural gas transportation,petrochemical industry, electric power, metallurgy, urban natural gas network of pipes,

The outside anticorrosion project of the metal pipes involved as well as the outside
anticorrosion project of the underground and overhead metallic conduit of the works
of petrochemical industry, natural gas and coal transportation.
gas pipe wrapping tape polyethylen butyl adheisve
inner wrap tape safe and clean, performs well in insulation, anticorrosion,
mechanical strength and anticollision, moreover it is of low water absorption,
long service life, wide usage and convenient in application.

1) The specification of the tape consists of two layers, adhesive and film
2) Inner layer: butyl rubber

3) Outer layer: polyethylene
4) Thickness: 0.**0 - 1.*7mm
5) Width: *0mm, *5mm, **0mm, **0mm, **0mm, **0mm
6) Length: *0 - **0m

Measurement	US Value	Metric Value	Test Method
Backing thickness	*2 mil	0.3mm	PSTC**3
Adhesive thickness	*3 mil	0.*4mm	PSTC**3
Adhesion to Steel	*8oz/in	4kg/cm	ASTM-D****0
Elongation	**0%	**0%	ASTM-D****0
Dielectric breakdown	*0 Kv/mm	*0 Kv/mm	ASTM-D****0
Insulation resistance	**8Ohm.m2	**8Ohm.m2	ASTM-D****0
Water absorption	<0.1%	<0.1%	ASTM-D***0
Maximum Temperature	**0ºF	*8ºC
Tensile	*0lb/in	.*8kg/mm	ASTM-D****9
Color	White /Black	White /Black

Product use:
1) Steel pipe pretreatment
1.1 Keeping the pipe external surface clean and dry.Remove the dust, oil, welding slag, burrs, grease and dirt on pipe surface.
1.2 Pipe surface prepared up-to a level of Sa 2 or 2 ½ or St 2/st by sand blasting.
1.3 After the precleaning operations, the pipe surface not smoothwhich may sharp the pipe coating should be burnished , the abrasive dust attached on the pipe surface should also be cleaned clearly.
1.4 If flash rusting occurs, the surfaces must be re-cleaned by blasting as above.
2) Coating &Wrapping application
2.1 Coating &wrapping application consist of primer application, inner tape coating ,outer tape coating .
2.2 weather condition
2.2.1 When the wind&sand was strongly, when the sand and dust covered on the surface of pipe, primer ,tape etc., should not be brushing primer and wrapping the tape if there is no reliable preventive measures.
2.2.2 When air humidity is greater than *0%,or when the pipe surface is wet from any precipitation, should not be brushing primer and wrapping tape.
3) Brushing primer
3.1 The brushing time should be control within 6 hours between the pipe surface treatment and brush primer During brush primer, pipe surface should be free from damp and pollution. If the pipe surface
rust return, should be re-pre-cleaned.
3.2 The primer should be mixed evenly in the container before brushing.
3.3 The primer should be applied uniformly, without any sags, floods, runs, drips, bare spot and over spray,
such as leakage brush, clot, streaming. The primer coat DFT shall not be less than ****0micron (**2mils)
3.4 After the primer dried, then wrapping the tape(It usually takes 3to 5 minutes.).
3.5 Consumption:
machine applicationapprox. 0,1 litre/m²
hand applicationapprox. 0,2 litre/m²
4) Wrap tape application
4.1 Wrap tape application consists of hand application and machine application.
4.2 The tape applied temperature must be above 5 degrees,the coating construction temperature shall be
more than *5 degrees as better .
4.3 The tape shall be spirally applied ,minimum overlap shall not be less than *0%.
4.4 When a new roll of tape started ,the ends shall be located to ensure the continuity of wrap tape using the
same method of application.
4.5 Outer tape applied method is the same as above.
5.Cutbacks
Cutbacks shall be a minimum 6inches(**0mm) from the ends of each pipe.The cutbacks may be tapered
or straight edge for the total thickness of the coating.
FAQ:

1. What is the payment terms.
T/T (Telegraphic Transfer) , L/C at sight,Western Union

بلد:	China
نموذج رقم:	XUNDA T100
سعر فوب:	2.5 ~ 3.6 / Roll ( Negotiable ) (قابل للتفاوض) أحصل على آخر سعر
الموقع:	-
سعر الحد الأدنى للطلب:	2.5 per Roll
الحد الأدني للطلب:	100 Roll
تفاصيل التغليف:	carton
موعد التسليم:	5-7days
القدرة على التوريد:	3000000 Roll per Month
نوع الدفع:	T/T, L/C
مجموعة المنتج :	XUNDA T100