الوصف
Features:
1, made from Portland cement and
silica together with other special strong actively chemical
materials
2, after the cement-based
permeating crystalline-type waterproof material mixed with
concrete, it can penetrate into the inside, and formulate the
crystals that won’t dissolve in water, so as to filling pores and
dense the concrete then prevent water. The concrete that after
dealing with the cement-based permeating crystalline-type
waterproof material, even few years later, the active substances
can be reactive and make the not fully hydrated substances into
crystals, then fill the later-formed cracks.
3, belongs to inorganic,
anti-aging, the expansion rate is equal to the concrete, the
waterproof age is basically the same with the structure and it
can strengthen the concrete, can extend the process of its
carbonation and prevent steel from corrosion.
4, it has self-repair function when
facing small cracks.
5, the process is simple, the
construction of non-fire operations, non-toxic, non-irritating
odor
6, can under the water pressure of
1.5~1.9MPa
7, simple operation, it can both
used in the front or the back side of water, can be coated on the
wet surface or can be covered by other coating, no need for the
leveling layer, no requirement for the protective film. For the
basement outdoor wall operation, it can be backfilled after 7
days and will not damage the waterproof coating
Application:
1, the rigid waterproof for
underground engineering and hydraulic engineering, e.g.
basements, bridges, cooling towers, kitchens, roofs, tunnels,
swimming pools and so on. can be the waterproof both for the
positive and back sides.
2, for the open-air environment,
water used in concrete structures, appropriate measures should be
adopted
3, for the structure that cracks
may change, using flexible material to fill the downing crack,
deformation crack, the Cement-based permeating crystalline-type
waterproof material is not suitable.
4, under 4℃, do
not operate.
Surface Treatment:
1, the surface should be stable,
clean, smooth, no dust, no oil, no shedding, and other detrital
materials
2, the obvious pore and hole must
be silted up by the cement mortar, the sharp edges should be
wiped out, recommend the cement mortar additive that mixed MB
NO.3 slurry
3,if the surface is dry, moist
the surface with clean water till there is no clear water before
operation
Operation Process:
1, base surface:
Check the concrete surface whether
it has any defect, or the left steel head, organic, oil painting,
and other bonding materials. For the crack, using wire brush to
make it, e.g. for the crack above 0.4mm, requiring a *5**0mm
U-groove, and clean the surface with wire brush or chisel or
high-pressure water gun, never leave any suspended
materials.
2, brushing:
(1), using semi-rigid nylon brush
when coating the Cement-based permeating crystalline-type
waterproof material
(2), brushing back and forth and
pay attention to the force, so as to ensure the bump at full
coating and with the same thickness
(3), for the operation on the plane
or stage, brushing the material evenly, especially for the front
and backlight sides, never make thick deposition, forbid the
thick place generates crack.
(4), for the over 0.4mm crack,
requiring a groove, then moist it, brushing the material of
concentrate slurry, after 1.5h strengthen it with semi-feeding
group of the material, then continue brushing the material, and
this needs two times, after the first time about **2h, make the
second, if for the first time the surface dries too quickly,
moist it before the second time.
Tips:
dealing with the surface according
to the requirements, if under the heat and sun exposure, cooling
the surface in order to reduce the temperature.
b, using brush , brushing the mixed
slurry on the surface evenly and make sure no flaws and
vulnerabilities.
c, after the first time of brushing
,wait for about **4 hours , brushing the second time, the
direction should be opposite for the two times.
Normal Amount:
1.2~1.4kg/m2
Thickness: 1.0~1.2mm
Ratio: powder: additive: water= *5:
3:5~7
Cautions:
1, do other covers after the
waterproof layer totally dry.
2, for a better effect, do not
operate under *5℃
or particularly damp and
unventilated situation
3, never mix the dry slurry with
water and use again
4, for the nodes, should process in
accordance with relevant requirements, add a fiber layer
5, under special situation, our
company can provide operation scheme by the technical
department.
Store Method:
Store in cool and dry place,
unopened product can be saved for one year.
Packing:
5kg permeating crystalline-type
master powder, *5kg/bag powder + 3kg emulsion (active chemical
additives)
| بلد: |
China |
| نموذج رقم: |
Mebong MB K11 Cement-based
|
| سعر فوب: |
(قابل للتفاوض)
أحصل على آخر سعر
|
| الموقع: |
- |
| سعر الحد الأدنى للطلب: |
- |
| الحد الأدني للطلب: |
1 ton |
| تفاصيل التغليف: |
- |
| موعد التسليم: |
- |
| القدرة على التوريد: |
500 tons/ month |
| نوع الدفع: |
- |
| مجموعة المنتج : |
Mebong Waterproof Series
|
