سعر فوب
أحصل على آخر سعر|
300 Piece Minimum Order
بلد:
China
نموذج رقم:
RP480/RP480N
سعر فوب:
الموقع:
-
سعر الحد الأدنى للطلب:
-
الحد الأدني للطلب:
300 Piece
تفاصيل التغليف:
Color box
موعد التسليم:
Within a month
القدرة على التوريد:
10000 Piece per Month
نوع الدفع:
L/C, T/T
مجموعة المنتج :
-
الشخص الذي يمكن الاتصال به Mr. Benny
Luqiao,pengjie, Taizhou, Zhejiang
Description:
1.The heavy-duty choice for small painting contractors, property owners, handymen and large contractors with frequent spraying needs.
2.Airless sprayers are easy to use, allow fast coverage,and provide high- quality finishes on a wide range of surfaces.
3.It apply meterial ip to 4 times faster than using a brush and 2 times faster than using a roller, helping you finish your projects faster.
RongPeng Airless Paint Sprayer-RP**0N/RP**0 :
| Model | RP**0N/RP**0 |
| Voltage/Frequency | **0V/*0HZ |
| Motor size | 1.0HP(**0W) |
| Max Pressure | ***0PSI |
| Standard Nozzle size | **7 |
| Spraying Width | ******0mm |
| Flow rate | 2.1L/min |
| Length of high pressure hose | *5M |
| Max. Pressure for the hose | *3Mpa |
Spray Gun Trouble Shooting:
|
Symptom |
Problem | Solution |
| Spray gun's body fluttering or spitting |
1.Spray gun's material level too low. 2.Container tipped too far. 3.Loose spray gun's fluid inlet connection. 4.Loose or damaged spray gun's fluid tip/seat. 5.Dry or loose spray gun's fluid needle packing nut. 6.Spray gun's air vent clogged.
|
1.Add material into spray gun's container. 2.Hold more upright. 3.Tighten. 4.Adjust or replace the spray gun's fluid tip/seat 5.Lubricate or tighten. 6.Clear the spray gun's vent hole.
|
| Pattern is arc |
1.Worm or loose spray gun's fluid nozzle. 2. Spray gun's material build up on air cap.
|
1.Tight or replace spray gun's fluid nozzle. 2.Remove obstructions from holes, but use meatal objects to clean.
|
| Patterm is not evenly spread |
1.Materoa; build up on air cap. 2. Spray gun's fluid nozzle dirty or worn.
|
1.Clean or replace spray gun's air cap. 2.clean or replace spray gun's fluid nozzle.
|
|
The center of pattern too narrow.
|
1. Spray gun's material too thin or not enought. 2.Atomization air pressure too high
|
1.Regulate material viscosity 2.Reduce air pressure.
|
|
Pattern width of fan sharp is not enough
|
1. Spray gun's material too thick 2.Atomization air pressure too low
|
1.Regulate material viscosity 2.Reduce air pressure |
|
Air leaking from air cap without pulling trigger
|
1.Sticking spray gun's valve stem
2.Contaminate on spray gun's air valve or seat 4.Broken spray gun's air valve spring 5.Bent spray gun's valve stem
|
1.Lubricate spray gun's valve stem
2.Clean spray gun's air valve or seat 4.Replace spray gun's air valve spring 5.Replace spray gun's valve stem
|
|
Spray gun fluid leaking from packing nut
|
1.Spray gun 's packing nut loose 2.Spray gun 's packing worm or dry
|
1.Tighten, but do not restrict needle 2.Peplace or lubricate (non-silicone oil)
|
|
Excessive overspray
|
1.Too high atomization pressure 2.Too far from work surface 3.Improper stroking (arcing ,spray gun motion too fast )
|
1.Reduce pressure 2.Adjust to proper distance 3.Move at moderate pace, parallel to surface
|
| Spray gun will not spray |
1.No pressure at spray gun 2.Spray gun 'sfluid control not open enough 3.Spray gun's fluid too heavy
|
1.Check spray gun's air lines 2.Open spray gun's fluid control 3.Thin spray gun's valve stem fluid or change to pressure feed system
|
Showroom:
Certificate :
Spray Gun Test And Equipments:
| بلد: | China |
| نموذج رقم: | RP480/RP480N |
| سعر فوب: | أحصل على آخر سعر |
| الموقع: | - |
| سعر الحد الأدنى للطلب: | - |
| الحد الأدني للطلب: | 300 Piece |
| تفاصيل التغليف: | Color box |
| موعد التسليم: | Within a month |
| القدرة على التوريد: | 10000 Piece per Month |
| نوع الدفع: | L/C, T/T |
| مجموعة المنتج : | - |
